Chevy Tahoe/Suburban Steering Sensor
From Combustory
(Difference between revisions)
Jvaughters (Talk | contribs) (New page: <anyweb>http://combustory.com/wiki/ads/ad_rtc.html</anyweb> {{default}} <!--------------------------------Featured picture------------------------------ {| id="mp-tfp" style="margin:4px ...) |
Jvaughters (Talk | contribs) |
||
| Line 26: | Line 26: | ||
| − | <big>''' | + | <big>'''Quick Instructions'''</big> |
| − | * | + | * Move seat all the way back and put steering tilt all the way up |
| − | * | + | * Start car and move steering until the coupling nut is facing down then shut of car |
| − | * | + | * Disconnect Battery and wait 15 minutes (This is to prevent the air bag from KILLING you) |
| − | * | + | * Remove front plastic under dash cover using 8mm socket with nut driver (4 screws) |
| − | * | + | * Remove the front sheet metal plenum using 8mm socket with nut driver (2 screws) |
| − | * | + | * Take off the center post using 15mm socket, deep socket or wrench (4 nuts) |
| − | * | + | * Take off the coupling nut using 15mm socket with breaker bar and remove bolt |
| − | * | + | * Remove lower steering column nuts using 15mm socket, deep socket or wrench (2 nuts) |
| + | * Remove upper steering column nuts using 15mm socket or deep socket with the 6" extension and socket wrench by going through the front plenum access (2 nuts) | ||
| + | * The steering column will drop down and then you can move the column out of the coupling | ||
| + | * Lay the lower flange on the brake pedal bar and have someone hold the steering wheel up | ||
| + | * Prop the steering wheel up with a 21" 2x4 on the seat | ||
| + | * Remove the sensor | ||
| + | ** By using the curved probe to push sensor out through the slots behind the plastic clips while gently pulling back the plastic clips at the same time until the sensor clears the clip | ||
| + | ** Do one clip at a time until all three are cleared | ||
| + | ** Push out evenly from behind each clip until the sensor is completely out | ||
| + | ** Slide Sensor off the shaft | ||
| + | * | ||
* [[Rockets]] (Coming) | * [[Rockets]] (Coming) | ||
* [[Helicopters]] (Coming) | * [[Helicopters]] (Coming) | ||
Revision as of 01:44, 11 April 2011
Welcome to Combustory
Any questions or comments:
- Send them to - combustor@combustory.com
|
Goal
My original Goal was to create a website that is the most comprehensive website for Automobiles. However, as I soon found out while looking for a Domain Name that there were not many good choices related to cars. Some how I came up with Combustory and it made me think of the History of Combustibles in general. So I decided on a site that would include all machines dependent on Combustibles. As you can see from the list below it is a fairly significant task that will require a world of help, so please feel free to join in the task by emailing me to create an account and start creating content.
File:Tools 1.jpg
Roadside Assistance Required
Contact: combustor@combustory.com
Quick Instructions
- Move seat all the way back and put steering tilt all the way up
- Start car and move steering until the coupling nut is facing down then shut of car
- Disconnect Battery and wait 15 minutes (This is to prevent the air bag from KILLING you)
- Remove front plastic under dash cover using 8mm socket with nut driver (4 screws)
- Remove the front sheet metal plenum using 8mm socket with nut driver (2 screws)
- Take off the center post using 15mm socket, deep socket or wrench (4 nuts)
- Take off the coupling nut using 15mm socket with breaker bar and remove bolt
- Remove lower steering column nuts using 15mm socket, deep socket or wrench (2 nuts)
- Remove upper steering column nuts using 15mm socket or deep socket with the 6" extension and socket wrench by going through the front plenum access (2 nuts)
- The steering column will drop down and then you can move the column out of the coupling
- Lay the lower flange on the brake pedal bar and have someone hold the steering wheel up
- Prop the steering wheel up with a 21" 2x4 on the seat
- Remove the sensor
- By using the curved probe to push sensor out through the slots behind the plastic clips while gently pulling back the plastic clips at the same time until the sensor clears the clip
- Do one clip at a time until all three are cleared
- Push out evenly from behind each clip until the sensor is completely out
- Slide Sensor off the shaft
- Rockets (Coming)
- Helicopters (Coming)
- Locomotives (Coming)
- General Electronics
